Carb CFM FAQ
Injector Sizing
Pistons & Ink · Free Tools

Injector
Sizing

Horsepower goal in, injector size out, in lb/hr and cc/min, sized at a safe 80 percent duty cycle with the right fuel math for gasoline or E85.

Your Combo

Target horsepower (flywheel)
Fuel & induction
Brake specific fuel consumption: 0.50 lb of fuel per horsepower-hour, typical for a naturally aspirated gasoline engine.
Cylinders
Maximum duty cycle (%)
80 percent leaves headroom for cold weather, voltage drops, and a tired pump. Race-only builds sometimes run 85 to 90, at their own risk.

Injector Required

—
lb/hr per injector
—
cc/min per injector
—
What common sizes support (this combo, your duty cycle)
Injector (lb/hr)243036426080
Max HP——————
Injector flow ratings assume the rated fuel pressure (commonly 43.5 psi). Raising base pressure raises flow; the pump has to hold that pressure at full demand or the math is fiction.

The math: BSFC does the work

Injector size = HP × BSFC ÷ (cylinders × duty)

Brake specific fuel consumption is how many pounds of fuel an engine burns per horsepower, per hour. Multiply by your horsepower goal for total fuel demand, then split it across the injectors with duty cycle headroom. That is the whole formula.

Why E85 needs so much more injector

E85 carries less energy per gallon, so the engine needs roughly a third more volume for the same power. That is baked into the E85 BSFC numbers here. It is also why E85 builds run out of injector and pump long before gasoline builds at the same power.

Too big is a real problem too

Oversized injectors make idle and cruise pulse widths so short the injector cannot meter consistently, and drivability suffers. Size for the goal with room to grow modestly, not for a fantasy number.

About this calculator

Injector sizing is a fuel-budget problem, and this calculator works it from the top down. The core equation: required flow per injector in lb/hr = target horsepower × BSFC ÷ (number of injectors × maximum duty cycle). BSFC, brake specific fuel consumption, is how many pounds of fuel an engine burns to make one horsepower for one hour, and it is where your fuel and induction choices enter the math through the presets: Gasoline NA at 0.50, Gasoline Boosted at 0.62, E85 NA at 0.68, E85 Boosted at 0.85 and Methanol NA at 1.00. E85 needs roughly a third more fuel volume than gasoline for the same power, methanol about double, and boost raises the number further because forced-induction engines run richer for cooling and safety margin. The result is also given in cc/min using the standard conversion the tool applies, lb/hr × 10.5.

Duty cycle is the other half of the discipline. It is the percentage of time the injector is held open at peak demand, and it is capped on purpose: the default here is 80%, because an injector run near 100% goes static, stops metering precisely, runs hot, and leaves you nothing for a cold night, a strong tailwind of dense air, or an engine that makes a little more than the dyno said. The results also include a support table: for each common size (24, 30, 36, 42, 60 and 80 lb/hr) it shows the maximum horsepower that size supports with your exact cylinder count, duty cycle and BSFC, with the smallest covering size marked as your pick. All of it is flywheel horsepower; if your goal is a wheel number, add your drivetrain loss first.

How to use it

  1. Enter your target flywheel horsepower. Be honest: size for the engine you are building, not the one in the group chat.
  2. Pick the preset that matches your fuel and induction: gasoline, E85 or methanol, naturally aspirated or boosted.
  3. Set your cylinder count and your duty-cycle ceiling. Leave it at 80% unless you have a specific, informed reason to push higher.
  4. Read the required flow in lb/hr and cc/min, then check the support table for the smallest common injector size that covers it, and confirm your fuel pump and lines can feed the total: per-injector flow times cylinder count is the system's full appetite.

Worked example

The page's defaults: 500 flywheel HP, gasoline NA, 8 cylinders, 80% duty. Requirement = 500 × 0.50 ÷ (8 × 0.80) = 39.1 lb/hr per injector (410 cc/min), and the support table names the 42 lb/hr injector as the pick. Now flip only the fuel preset to E85 Boosted (0.85): the same 500 HP needs 500 × 0.85 ÷ 6.4 = 66.4 lb/hr, which blows past the 60 lb/hr size entirely and lands on 80s. Same engine, same power, 70% more injector, purely because of what is in the tank and the blower on top.

FAQ

What size injectors for 500 hp?

On a V8 running gasoline, naturally aspirated: about 39 lb/hr, so 42s are the pick. Boosted on gasoline: about 48 lb/hr, so 60s. On E85 boosted: about 66 lb/hr, so 80s. All at 80 percent duty cycle. Run your exact combo above.

Why not just run huge injectors to be safe?

Oversized injectors idle poorly because the pulse width at idle gets too short to meter accurately. Size for the goal with 80 percent duty at peak, and let the pump and regulator keep up. Room to grow means one size up, not three.

Does fuel pressure change injector size?

Yes. Flow rises with the square root of the pressure ratio: an injector rated 42 lb/hr at 43.5 psi flows about 48 lb/hr at 58 psi. This calculator assumes rated pressure. If your system runs higher base pressure, your injectors effectively run one size larger.

Why not just run the injectors at 100% duty cycle?

Because at 100% an injector is no longer metering; it is simply open. Control gets sloppy, the injector runs hot, and you have zero reserve for cold dense air, a slightly stronger engine than expected, or fuel pressure that sags at the top end. The industry working ceiling is 80 to 85%, which is why this calculator defaults to 80%: the headroom is not waste, it is the margin that keeps a full-throttle pull from going lean.

About Pistons & Ink

Built by enthusiasts,
for enthusiasts

Pistons & Ink is a digital product studio based in Ocala, Florida, building web and mobile products for the automotive enthusiast community. We come from the custom car and truck world — lowriders, minitrucks, C10s, restomods — and we build tools we'd use ourselves.

This fuel injector calculator is one of 11 free tools in the Pistons & Ink Digital Toolbox, built for the aftermarket auto industry. If it helped you, the rest of the toolbox is right here.

Visit Pistons & Ink →
From the Guides Library
Fuel Injector Sizing for Your Horsepower Goal
The BSFC formula for gasoline and E85, boosted and naturally aspirated, plus the pump and duty-cycle checks that make the math hold.
Read the Guide