Tire Calculator Tire Change FAQ
Gear Ratio Calculator
Pistons & Ink · Free Tools

Gear Ratio
Calculator

What RPM will you turn at highway speed? What did that tire change really do to your gearing? Two quick calculators with the math the shops use.

Cruise RPM & Speed

Tire diameter (inches)
Not sure? The tire calculator converts any tire size to diameter.
Axle ratio
Transmission gear ratio
Common top gears: 0.70 (700R4 / 4L60E family), 0.75 (4L80E), 0.67 (6L80), 0.64 (10L80), 1.00 (direct drive, most 3-speeds in high gear).
Road speed (MPH)
Result
—
Engine RPM at speed
—
Going the other way: at 2,500 RPM this combo runs —. Transfer case in low range? Multiply the trans ratio by the low-range ratio (2.72 is common) and use that as the gear ratio.

Tire Change: Effective Ratio

Stock tire diameter (inches)
New tire diameter (inches)
Current axle ratio
—
Effective ratio now
—
Ratio to restore stock
—
Restoring stock performance is the baseline. Towing heavy or chasing off-the-line snap? Go one step deeper than the restore number. Mostly highway? The restore number is the sweet spot.

How the math works

The 336 formula

Engine RPM = MPH × axle ratio × transmission gear ratio × 336 ÷ tire diameter in inches. The 336 folds the unit conversions (inches per mile, minutes per hour, pi) into one constant. It is the same formula printed in every gear vendor's catalog.

Taller tires act like taller gears

A bigger tire covers more ground per revolution, so the engine turns slower for the same speed, exactly as if you installed a numerically lower axle ratio. That is why a truck on 35s with stock gears feels lazy off the line and hunts for gears on grades.

Your speedometer is off too

The same percentage your effective ratio changed is the percentage your speedometer and odometer are wrong by, until the computer is corrected for the new tire size. On modern trucks that correction is a setting in a tuner or a dealer flash, not a gear swap in the dash.

About this calculator

This page holds two calculators that answer the two gearing questions every truck owner eventually asks. The first: at highway speed, how hard will the engine be turning? The second: I changed tire size, so what did that do to my gearing, and which ring and pinion gets the feel back? Both run on one equation. Cruise RPM = MPH × 336 × axle ratio × transmission gear ratio ÷ tire diameter in inches. The 336 is not magic; it folds three constants together, the 63,360 inches in a mile, the 60 minutes in an hour, and π for the tire's circumference (63,360 ÷ 60 ÷ π = 336.1, rounded the way the industry has always rounded it). Asking the question the other way, speed at a given RPM, is the same equation turned inside out.

The tire-change half works on proportion. Your effective ratio is what your current gears behave like after the tire swap: axle ratio × old diameter ÷ new diameter. Taller tires divide the ratio down, which is why a truck on 35s with 3.42s feels lazy off the line and the transmission hunts on grades. The ratio that restores the stock relationship is axle ratio × new diameter ÷ old diameter, and the tool then names the closest commonly available gear set from the standard ladder (2.73, 3.08, 3.23, 3.31, 3.42, 3.55, 3.73, 3.90, 4.10, 4.30, 4.56, 4.88, 5.13, 5.38), because gear sets come in steps, not in any number you can dream up.

How to use it

  1. For cruise RPM: enter your tire diameter, axle ratio, the transmission gear you cruise in (1.00 for a direct-drive gear, about 0.70 for a typical overdrive) and your speed. Read the RPM, plus how fast you would be going at 2,500 RPM.
  2. For a tire change: enter your old and new tire diameters and your current axle ratio.
  3. Read the effective ratio (what your gears feel like now), the exact ratio that restores stock performance, and the closest real gear set you can actually buy.

Worked example

The page's defaults: at 70 MPH on 33 inch tires with 3.73 gears in a 0.70 overdrive, the engine turns 70 × 336 × 3.73 × 0.70 ÷ 33 = 1,861 RPM, and at 2,500 RPM that combination would be running 94 MPH. Now the tire swap, using the second panel's defaults: going from 31s to 35s on 3.42 gears makes them perform like a 3.03, a noticeable step lazier. Restoring the stock feel takes a 3.86, which does not exist on the shelf, so the tool points you to the closest common gear set, a 3.90.

FAQ

What RPM will I turn at 70 mph with 33 inch tires and 3.73 gears?

It depends on your top gear ratio. With a 0.70 overdrive, about 1,860 RPM. In direct drive (1.00), about 2,660 RPM. Run your exact combo in the calculator above.

I put bigger tires on. What gear ratio do I need?

Multiply your current ratio by the new tire diameter and divide by the old tire diameter. A truck with 3.42 gears and 31 inch tires that moves to 35s needs about 3.86 to perform like stock, so a 3.90 or 4.10 is the practical choice since ratios only come in set steps.

Does a gear swap change my actual top speed?

It changes the RPM where top speed happens, not the truck's aerodynamic or power limits. Deeper gears usually make a truck feel stronger everywhere at the cost of higher cruise RPM and fuel use. The calculator shows the trade exactly.

Where does the 336 in the RPM formula come from?

It is three constants folded into one. A mile is 63,360 inches, an hour is 60 minutes, and a tire's circumference is π times its diameter. Divide 63,360 by 60 and then by π and you get 336.1, which the industry rounds to 336. Multiply speed by 336 by both gear ratios and divide by tire diameter and the units cancel into clean engine RPM.

About Pistons & Ink

Built by enthusiasts,
for enthusiasts

Pistons & Ink is a digital product studio based in Ocala, Florida, building web and mobile products for the automotive enthusiast community. We come from the custom car and truck world — lowriders, minitrucks, C10s, restomods — and we build tools we'd use ourselves.

This gear ratio calculator is one of 11 free tools in the Pistons & Ink Digital Toolbox, built for the aftermarket auto industry. If it helped you, the rest of the toolbox is right here.

Visit Pistons & Ink →
From the Guides Library
Choosing the Right Gear Ratio for Bigger Tires
The effective-ratio formula, cruise-rpm checks, and when a tow rig or crawler should go a step deeper than stock.
Read the Guide