Famous Combos Overbore Table FAQ
Displacement Calculator
Pistons & Ink · Free Tools

Engine
Displacement

Bore, stroke, and cylinder count in; cubic inches, cc, and liters out. With the famous combos one tap away and an overbore table for planning your rebuild.

Your Engine

Units
Bore (inches)
Stroke (inches)
Cylinders
Odd count? Type any number here instead:
Famous combos
One tap loads the factory bore, stroke, and cylinder count. Badges are rounded by the factories; the calculator shows the true number.

Displacement

—
Cubic Inches
—
Cubic Centimeters
—
Liters
—
Same engine, bored over
OverboreNew boreDisplacementGain
How far a block can safely go depends on the casting and wall thickness. Sonic checking is the only real answer; this table is the math, not permission.

The math, in one line

Displacement = 0.7854 × bore² × stroke × number of cylinders
0.7854 is π ÷ 4, the circle-area factor. Bore and stroke in inches give cubic inches directly. One cubic inch is 16.387 cc, and 1,000 cc is a liter.

Bore is squared, stroke is not

Displacement grows with the square of the bore but only in step with the stroke. That is why a small overbore adds up across eight cylinders, and why stroker cranks are the bigger lever when you want real cubes from the same block.

Badges are rounded

A "350" is 349.85 cubic inches. A "5.0" Coyote is 302 cubes and 4,951 cc, while a pushrod Ford 5.0 is a different 302 with different bore and stroke. The badge is marketing rounding; this calculator gives you the true figure for the parts in front of you.

Measure, do not assume

Used blocks get bored. If you are calculating for a build, measure the bore with a bore gauge or calipers at the top of the ring travel, and confirm the crank stroke from the crank casting or a piston-travel measurement, not the badge on the fender.

About this calculator

Displacement is the total volume an engine's pistons sweep, and it comes from exactly three numbers: bore, stroke and cylinder count. The formula is the volume of a cylinder times the number of cylinders: 0.7854 × bore² × stroke × cylinders, where 0.7854 is π/4, the shortcut that turns a bore diameter into a piston's area. Work it in inches and you get cubic inches; the tool then multiplies by 16.387064 for cubic centimeters and divides by 1,000 for liters. Metric builders can enter bore and stroke in millimeters instead, converted at 25.4 mm to the inch before the same math runs. Nothing else hides in the number: deck height, gaskets and combustion chambers change compression, never displacement.

Two planning aids sit alongside the headline number. The preset list loads the famous factory combinations, the ones bench racing runs on, so you can see what a 350, a 383 or a big-block's specs actually multiply out to. And the overbore table shows the same engine at common rebuild overbores (0.010 to 0.060 inch in the inch view) so you can see exactly how many cubes a cleanup bore buys before you order pistons. That table settles a real shop question: boring is for restoring the bore, and the displacement it adds is a side effect measured in single digits, while stroking is how displacement is actually bought.

How to use it

  1. Enter your bore and stroke. Standard bore, or the overbore you are planning, but be honest about which one you typed.
  2. Pick the cylinder count, and switch the unit toggle if you are working in millimeters.
  3. Read the displacement in cubic inches, cc and liters in the results panel.
  4. Before a rebuild, scan the overbore table for your combination to see what each cleanup pass is worth in cubes, and compare it with what a stroker crank would give you instead.

Worked example

The classic 383 stroker small-block: a 4.030 inch bore (a 350 block bored 0.030 over) with a 3.750 inch stroker crank and 8 cylinders. Run it: 0.7854 × 4.030² × 3.750 × 8 = 382.7 cubic inches, 6,271 cc, 6.27 liters. Now compare the bore-only route: that same 4.030 bore on the stock 3.480 stroke gives 355.1 ci, the familiar "355." Thirty thousandths of bore bought about 5 cubes; the crank bought 28 more. That is the whole stroker argument in one line of arithmetic.

FAQ

Why is a Chevy 350 actually 349 cubic inches?

Because the badge is rounded. A 4.000 inch bore and 3.480 inch stroke across 8 cylinders works out to 349.85 cubic inches, and Chevrolet rounded to 350. Most famous engine sizes are rounded the same way. Load the Chevy 350 preset above and see it.

What is a stroker engine?

A stroker uses a crankshaft with a longer stroke than stock in the same block. The classic example is the 383 small-block Chevy: a 350 block bored 0.030 over with a 3.750 inch stroke crank in place of the stock 3.480. Same block, 33 more cubic inches. The preset is above.

How much displacement does boring 0.030 over add?

On a typical small-block V8, about 5 to 7 cubic inches. The overbore table next to your result shows the exact number for your bore and stroke combination, from +0.010 to +0.060.

Does displacement alone tell me horsepower?

No. Displacement sets the ceiling, but airflow, compression, cam timing, and induction decide how close you get. A healthy street engine makes roughly 1 horsepower per cubic inch; strong builds exceed it. Displacement is the first number in the plan, not the last.

About Pistons & Ink

Built by enthusiasts,
for enthusiasts

Pistons & Ink is a digital product studio based in Ocala, Florida, building web and mobile products for the automotive enthusiast community. We come from the custom car and truck world — lowriders, minitrucks, C10s, restomods — and we build tools we'd use ourselves.

This displacement calculator is one of 11 free tools in the Pistons & Ink Digital Toolbox, built for the aftermarket auto industry. If it helped you, the rest of the toolbox is right here.

Visit Pistons & Ink →