How much air your engine actually breathes, and the carb size that matches. Displacement, redline, and how hard the engine works, nothing more.
| 500 | 600 | 650 | 700 | 750 | 800 | 850 | 950 |
|---|---|---|---|---|---|---|---|
| — | — | — | — | — | — | — | — |
The 3456 converts cubic inches per minute into cubic feet and accounts for a four-stroke engine breathing once every two revolutions. Every carb maker's sizing chart is this formula with a VE assumption baked in.
Four-barrel carbs are flow-rated at 1.5 inches of mercury of vacuum; two-barrels at 3.0. A "600" from one test bench is not identical to a "600" from another, and dry-flow ratings differ from wet. Treat the output as a size class, not a lab number.
An engine only pulls its rated CFM at full throttle near redline. The rest of the time a too-big carb weakens the signal at the venturi, which dulls response and mileage. When between sizes on a street car, choose the smaller one.
A carburetor has one job: pass as much air as the engine can inhale, with fuel metered into it accurately. This calculator sizes that job with the standard airflow equation: CFM = displacement (ci) × RPM × volumetric efficiency ÷ 3,456. The constant is two facts folded together. A four-stroke cylinder only inhales once every two revolutions, and a cubic foot holds 1,728 cubic inches; 1,728 × 2 = 3,456. Volumetric efficiency, VE, is how completely your engine actually fills its cylinders compared to the theoretical sweep, and it is the input that separates a catalog guess from a real answer, so the tool gives you five honest presets instead of one flattering one: Stock at 80%, Mild street at 85%, Street/strip at 90%, Race at 95% and All-out at 100%.
The output is a requirement, not a dare. Alongside the raw CFM number, the size ladder (500, 600, 650, 700, 750, 800, 850 and 950 CFM, the sizes street carbs are actually sold in) marks each size too small, covers it, or your pick: the smallest carb that covers the requirement. That framing is deliberate. A carb meters fuel off the air signal through its boosters, and an oversized carb weakens that signal at low RPM, which costs you throttle response and clean part-throttle manners in exchange for airflow your engine never asked for. If your combination outruns the ladder entirely, the tool says so plainly: you are in Dominator territory, and that is a different conversation.
The page's defaults: a 350 ci engine at 5,500 RPM on the Mild street preset (85% VE). Requirement = 350 × 5,500 × 0.85 ÷ 3,456 = 473 CFM, so the ladder names the 500 CFM carb as your pick. Push the same engine to a theoretical 100% VE and it needs 557 CFM, still only a 600. That is the pattern this calculator exists to show: most street small-blocks are honestly 500-600 CFM engines, and the 750 on the shelf is usually a throttle-response downgrade wearing a bigger number.
A mild 350 that spins to 5,500 RPM needs about 475 CFM by the formula and runs best on a 600 CFM carb. A built 350 turning 6,500 needs roughly 590 CFM and wears a 650 or 750 depending on cam and intake. Run your exact redline above.
Yes. An oversized carb weakens the vacuum signal at the booster, which dulls throttle response and low-speed metering. The engine only pulls rated CFM at full throttle near redline; everywhere else, smaller meters better. This is why 750s on mild small-blocks feel soggy.
For draw-through and blow-through carb setups, boost raises effective VE well past 100 percent, so treat the all-out setting as a floor and size up with your tuner. For modern EFI engines, the injector sizing calculator is the right tool.
Almost never on a street engine. The calculator returns the airflow your engine can actually consume at full song. A much larger carb flows that same air at a weaker signal through the boosters, which dulls fuel metering, throttle response and low-speed manners. Oversizing only pays when the engine genuinely out-breathes the smaller carb, and the VE presets above are how you test that honestly instead of hopefully.
Pistons & Ink is a digital product studio based in Ocala, Florida, building web and mobile products for the automotive enthusiast community. We come from the custom car and truck world — lowriders, minitrucks, C10s, restomods — and we build tools we'd use ourselves.
This carburetor CFM calculator is one of 11 free tools in the Pistons & Ink Digital Toolbox, built for the aftermarket auto industry. If it helped you, the rest of the toolbox is right here.
Visit Pistons & Ink →